We have a great selection of drills from dealers across the country. We list models from Astec, Ditch Witch, Driltech, E-Z Drill, Reedrill, Tamrock, Vermeer and more. Check out our recent listings or ... more about Drills
Machine description: - Equipped with YH80A Drifter, - Unit needs nothing is currently running on a job at this time., - Has newer paint job, - Manual rod changer, - Long boom... more info about the 2000 Ingersoll Rand ECM590.
Machine description: - Equipped with YH80A Drifter, - Ready to work, - Repairs needed are one door with broken hinges, - Fuel stop solenoid, - This machine has a new air end and has less than 200 hours on hydraulic pump... more info about the 1997 Ingersoll Rand ECM590.
Machine description: - Equipped with YH80A Drifter, -Only known issue is the engine Boggs down under a hydraulic pressure load everything works as intended but noticeable lack of performance due to lower engine rpm's . Po... more info about the 1999 Ingersoll Rand ECM590.
Machine description: - True low hour 1995 Furukawa HCR9ES, - Unit has been fully serviced., - Throttle cable has been replaced., - ALL but 2 cylinders have been resealed., The only 2 that we did not do, was the inner boom... more info about the 1995 Furukawa HCR9ES.
Machine description: Montabert HC160 Drifter, Set up for T51, Cummins Diesel Engine, Unit is showing 2642.7 engine hours, We estimate approximately 12,642.7 total frame hours., And 4513 percussion hours... more info about the 2004 Ingersoll Rand ECM660 III.
Machine description: Montabert HC160 Drifter, Set up for T51, Cummins Diesel Engine, Unit is showing 2642.7 engine hours, We estimate approximately 12,642.7 total frame hours., And 4513 percussion hours... more info about the 2004 Atlas Copco ECM660 III.
Machine description: 3.5” – 4.5” Inch Class*, CAT 3126 Diesel Engine*, Self-Contained Hydraulic Drill*, HPR1H Hydraulic Drifter, New Injection Pump 2017, Handles a 20’ft starter steel, Set up for T45, Low frame H... more info about the 1998 Reedrill 300.
Machine description: 3.5” – 4.5” Inch Class*, CAT 3126 Diesel Engine*, Self-Contained Hydraulic Drill*, HPR1H Hydraulic Drifter, New Injection Pump 2017, Handles a 20’ft starter steel, Set up for T45, Low frame H... more info about the 1998 Gardner-Denver 300.
Machine description: - Comes with YH70, not currently installed but will be mounted for transport, - Batteries need charging or replaced so could not stand machine up at time of photos., - Missing wall and doors need to ... more info about the 2003 Ingersoll Rand ECM590.
Machine description: - Comes with YH70 not currently installed but will be mounted for transport, - This unit has tracking issues will move but unknown if it's the final drives or hydraulic motors., - Hammer needs to be ... more info about the 2004 Ingersoll Rand ECM590.
Machine description: 3.5 - 4.5 Inch Class*, COP 1840 HEX Hammer fresh rebuild*, Cummings 6.7*, Low Hours, Great Condition, Total Hours 2250, Percussion Hours 1300... more info about the 2012 Atlas Copco POWERROC T35.
Machine description: 2.5 - 3.5 Inch Class*, Montabert HC109 Drifter*, Excellent Condition*, Engine Hours 5416.2, Percussion has ONLY **933 Total Percussion hours since new***, HC109 Drifter was last rebuilt June 2015 – ... more info about the 2005 Ingersoll Rand ECM585.
Machine description: 3.5 - 4.5 Inch Class*, Long Mast 20' FT Steel*, Cat Engine*, Unit is still in use.,, 2005 Atlas Copco ROC D7-11 LF, These Photos were taken March 29th, 2016 when the unit had 5798 engine hours & 1494... more info about the 2005 Atlas Copco ROC D7-LM.
Machine description: 3.5 - 4.5 Inch Class*, HCR120 Drifter w/ 2287 Percussion Hours*, Cummins Diesel w/ 5,828 Hours*, Enclosed Cab w/ AC, Set Up for T51, Rod Changer w/ One-Lever Control... more info about the 2002 Ingersoll Rand ECM660 II.
Machine description: 3.5 - 4.5 Inch Class*, COP Drifter*, CAT C-7 Tier III Diesel Engine*, Set up for T51 Drill Steel, Low hours, 3212 total hours, 976 percussion hours, Unit is still currently being used but is availabl... more info about the 2009 Atlas Copco ROC D9.
Machine description: 4.5” – 5.5” Inch Class*, CAT C11 Diesel Engine*, HC200A Drifter set up for GT60 Rods*, Caterpillar C11 Diesel Engine, Montabert HC200A drifter., Recent new hydraulic Pump, Aprox. 11800 total fr... more info about the 2007 Ingersoll Rand ECM720.
Machine description: 4.5 - 5.5 Inch Class*, Montabert HC200A Drifter*, Cat C11 Engine*, Set up for 60mm drill steel, Only 3570 Total Hours... more info about the 2008 Ingersoll Rand ECM720.
Click for Phone Number
