Machine description: UNDER DEPOSIT--Ingersoll Rand ECM660-III Crawler Hydraulic Drill w/ Cummins, AC cab, T51 rod changer, lube system, dust suppression system... more info about the 2005 Ingersoll Rand ECM660 III.
Machine description: EROPS, AC, HEAT, CUMMINS 6CTHA8.3 ENGINE, 13" STEEL TRACKS, 30° GRADEABILITY, HC160 REVERSE HYD. DRIFTER, STRATA SENSE DRILLING AUTOMATICS, 350CFM AIR COMPRESSOR, AIR VACUUM DUST COLLECTOR, AUTO ROD ... more info about the 2005 Ingersoll Rand ECM660 III.
Machine description: - Equipped with YH80A Drifter, - Repairs needed or in the process of being repaired, - Dust collector top new part has been fabricated need's installed, - Rod changer arm is broken have new parts to... more info about the 2006 Ingersoll Rand ECM590.
Machine description: - Equipped with YH80A Drifter, - Mechanic believes there is a broken pin in the fuel injection pump machine will idle but will not idle up., - Other repairs needed are inoperable fuel stop solenoid... more info about the 2004 Ingersoll Rand ECM590.
Machine description: - Equipped with YH80A Drifter, - Unit needs nothing is currently running on a job at this time., - Has newer paint job, - Manual rod changer, - Long boom... more info about the 2000 Ingersoll Rand ECM590.
Machine description: - Equipped with YH80A Drifter, - Ready to work, - Repairs needed are one door with broken hinges, - Fuel stop solenoid, - This machine has a new air end and has less than 200 hours on hydraulic pump... more info about the 1997 Ingersoll Rand ECM590.
Machine description: - Equipped with YH80A Drifter, -Only known issue is the engine Boggs down under a hydraulic pressure load everything works as intended but noticeable lack of performance due to lower engine rpm's . Po... more info about the 1999 Ingersoll Rand ECM590.
Machine description: Montabert HC160 Drifter, Set up for T51, Cummins Diesel Engine, Unit is showing 2642.7 engine hours, We estimate approximately 12,642.7 total frame hours., And 4513 percussion hours... more info about the 2004 Ingersoll Rand ECM660 III.
Machine description: - Comes with YH70, not currently installed but will be mounted for transport, - Batteries need charging or replaced so could not stand machine up at time of photos., - Missing wall and doors need to ... more info about the 2003 Ingersoll Rand ECM590.
Machine description: - Comes with YH70 not currently installed but will be mounted for transport, - This unit has tracking issues will move but unknown if it's the final drives or hydraulic motors., - Hammer needs to be ... more info about the 2004 Ingersoll Rand ECM590.
Machine description: 3.5 - 4.5 Inch Class*, HCR120 Drifter w/ 2287 Percussion Hours*, Cummins Diesel w/ 5,828 Hours*, Enclosed Cab w/ AC, Set Up for T51, Rod Changer w/ One-Lever Control... more info about the 2002 Ingersoll Rand ECM660 II.
Machine description: 4.5” – 5.5” Inch Class*, CAT C11 Diesel Engine*, HC200A Drifter set up for GT60 Rods*, Caterpillar C11 Diesel Engine, Montabert HC200A drifter., Recent new hydraulic Pump, Aprox. 11800 total fr... more info about the 2007 Ingersoll Rand ECM720.
Machine description: 4.5 - 5.5 Inch Class*, Montabert HC200A Drifter*, Cat C11 Engine*, Set up for 60mm drill steel, Only 3570 Total Hours... more info about the 2008 Ingersoll Rand ECM720.
Machine description: 4.5 - 5.5 Inch Class*, Montabert HC200A Drifter*, CAT Engine*, Set up to Handle GT60 Tooling, Dust Collector, Water Injection... more info about the 2003 Ingersoll Rand ECM720.
Machine description: Montabert HC200A Drifter - '0' hours on fresh service, CAT Engine, Set up for 60mm drill steel, Onboard Air of 480 CFM @ 150 PSI, 5500 total frame hours, 2012 percussion hours w/ '0' hours on new serv... more info about the 2007 Ingersoll Rand ECM720.
Machine description: 3.5 - 4.5 Inch Class*, HC200A Drifter*, CATERPILLAR 3306 Diesel Engine*, Extendable Boom, Onboard Ingersoll-Rand 420 CFM @ 150 PSI Air Compressor, Rod Changer, Ready to ROCK & ROLL!... more info about the 1999 Ingersoll Rand ECM690.
Machine description: 4.5” – 5.5” Inch Class*, CATERPILLAR Diesel Engine*, YH Series Drifter*, YH110V Hydraulic Drifter, Set up for T51, CAT 3306 Diesel Engine, Extendable Boom, Rod Changer... more info about the 1996 Ingersoll Rand ECM690.
Machine description: 3.5 - 4.5 Inch Class*, HC160R Drifter w/ Only 82 Percussion Hours since Rebuild*, Cummins Diesel Engine*, 7572 Engine Hours, 2517 Percussion Hours, Extendable Boom, Digital Angle Indicator, Auto Rod C... more info about the 2005 Ingersoll Rand ECM660 III.